This tool can be found on the Steel Tube Institute website.CONTENTS Dimensions and Properties 1 General Design Considerations 2 Design 01 Flexural Members 3 Design 01 Compression Members 4 Design ofTension Members 5 Design 01 Members Subject to Combined Forces 6 Design Considerations lor Bolts 7 Design Considerations lor Welds 8 Design 01 Connecting Elements 9 Design 01 Simple Shear Connections 10 Design 01 Partially Restrained Moment Connections 11 Design 01 Fully Restrained Moment Connections 12 Design 01 Bracing Connections and Truss Connections 13 Design 01 Beam Bearing Plates, Col. In order to ease this transition to the 2016 Specification, the Steel Tube Institute has produced a Limit State Table that details the various limit states, where they can be found in the 2016 Specification, what variable substitutions need to be made, and what the analogous check was in the 2010 Specification. We are often sent into Parts 9 or 10 of the 15th Edition Steel Construction Manual. Designers will find that not all pertinent checks are detailed in the Specification itself (whether it be Chapter J or K).In most other connections, it does not give such guidance it is up to the designer to determine which limit states could control.
#Aisc 14th edition aisc 360 10 manual
In this case, the Manual makes explicitly clear that a certain limit state will not control. This section of the Manual states that as long as the HSS wall is not a slender element, plastification will not control. In AISC 360-16, punching shear of the HSS wall is now checked with equation 10-7 in Part 10 of the 15th Edition Steel Construction Manual. In AISC 360-10, a shear plate connection checked punching shear in the HSS wall per equation K1-3.No longer is a table given that details which limit state is going to control the HSS connection as long as we are within certain parameters. Much like we already do for WF connections, we will check several limit states. However, because of this, more checks will need to be made to ensure the controlling limit state is accounted for. The limits of applicability for most rectangular HSS connections have been removed, giving the designer more perceived freedom. Therefore, the checks to the HSS wall can be made using the equations furnished in Chapter J for webs by substituting the WF variables for HSS variables. Both could be considered thin plate members spanning to supports on each side the HSS wall spanning to its sidewalls, the WF web spanning to the flanges. It’s easiest to navigate the new Specification by recognizing the similarities between connecting to the face of a rectangular HSS and connecting to the web of a wide-flange. There have not been many changes to the Specification where connections to round HSS are concerned most of the changes occurred with rectangular members. Although this is only shown for certain connections in Chapter K, the distance to the end of the member should be considered globally. The new limit of applicability states that if a connection is made closer than a certain distance from a member’s end, extra steps must be made to assure the adequacy of the connection. In the 2016 Specification, there is also a limit pertaining to the end of a member, however, this is not a new phenomenon. If the limits are not met, an engineer should use rational analysis to check the connection rather than pulling one equation from the table. The 2010 tables also contained a long list of limits of applicability, which may have made engineers feel that if the limits aren’t met, the connection can’t be done. In the 2010 Specification, the tables in Chapter K were easy to use, but contained a lot of repetition of information contained elsewhere in the Specification. The introduction to Chapter K now contains a statement that the requirements of Chapter J also apply. Chapter K no longer contains all the information needed to design HSS connections, but now consists of requirements that aren’t already covered in other parts of the specification, namely Chapter J. In 2016, the title is “Additional Requirements for HSS and Box-Section Connections”. In 2010, the chapter was titled “Design of HSS and Box Member Connections,” and it contained the majority of the information necessary to design connections with HSS. Technical Consultant, Steel Tube InstituteĪs you are probably aware, there have been many changes to Chapter K of AISC 360-16.
0 kommentar(er)
